crucial storage executive sanitize drive

#Crucial storage executive sanitize drive serial
#Crucial storage executive sanitize drive software

Sata Link Speed : Gen1 (1.5 Gbps) Temp(C) : 47 Drive information is retrieved successfully CMD_STATUS : Success STATUS_CODE : 0 Copyright (C) 2015 Micron Technology, Inc./msecli -X -B -n /dev/sdb Sanitizing the drive will erase all of it's saved data.

#Crucial storage executive sanitize drive serial

Secure erase cant be done, i dont know the PW./msecli -L Device Name : /dev/sdb Model No : Crucial_CT128M550SSD4 Serial No : * FW-Rev : MU01 Total Size : 128.04GB Drive Status : Attention! Drive is in security locked state.

but also cant reset the drive, i even tried PSID and Santize fuctions. still under linux i was found a newer version of Micron's tool(3.24), it was perfect, in the meaning of correct stdouts. at W7 the GUI freezes, i was only able to commucate with the drive under CLI, but after a few commands, its gone - under Arch the Micron Tool 3.15 was able to start the gui reads the datas, etc and said the sanitize was complete, however the drive is in locked state, the cli program was really informatic(said i must secure erase the drive), but sadly also cant sanitize the drive, however it seem complete. first of all: - W8.1 is not suitable for Crucial's own application, cant even recognize any kind of drive.

i spend a lot of time, getting this drive back to life. Logical Unit WWN Device Identifier: 5**************** NAA : 5 IEEE OUI : ****** Unique ID : ********** Device Sleep: DEVSLP Exit Timeout (DETO): 50 ms (drive) Minimum DEVSLP Assertion Time (MDAT): 10 ms (drive) Checksum: correct

#Crucial storage executive sanitize drive software

media change) * Software settings preservation Device Sleep (DEVSLP) * SMART Command Transport (SCT) feature set * SCT Write Same (AC2) * SCT Features Control (AC4) * SCT Data Tables (AC5) * reserved 69 * reserved 69 * Data Set Management TRIM supported (limit 8 blocks) * Deterministic read ZEROs after TRIM Security: Master password revision code = 65534 supported enabled locked not frozen not expired: security count supported: enhanced erase Security level high 2min for SECURITY ERASE UNIT. Hdparm -I /dev/sdb /dev/sdb: ATA device, with non-removable media Model Number: Crucial_CT128M550SSD4 Serial Number: ************ Firmware Revision: MU01 Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0 Standards: Used: unknown (minor revision code 0x0028) Supported: 9 8 7 6 5 Likely used: 9 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 - CHS current addressable sectors: 16514064 LBA user addressable sectors: 250069680 LBA48 user addressable sectors: 250069680 Logical Sector size: 512 bytes Physical Sector size: 4096 bytes Logical Sector-0 offset: 0 bytes device size with M = 1024*1024: 122104 MBytes device size with M = 1000*1000: 128035 MBytes (128 GB) cache/buffer size = unknown Form Factor: less than 1.8 inch Nominal Media Rotation Rate: Solid State Device Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, with device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Advanced power management level: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set * Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * DOWNLOAD_MICROCODE * Advanced Power Management feature set SET_MAX security extension * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test * General Purpose Logging feature set * WRITE_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Gen3 signaling speed (6.0Gb/s) * Native Command Queueing (NCQ) * Phy event counters * NCQ priority information * READ_LOG_DMA_EXT equivalent to READ_LOG_EXT * DMA Setup Auto-Activate optimization Device-initiated interface power management Asynchronous notification (eg.